Can-Am Maverick Forum banner

1 - 17 of 17 Posts

·
Registered
Joined
·
69 Posts
Discussion Starter #1
Just wanted to show you guys how it is coming together. Think I'm going to call it almost done, still would like to install a winch into the bumper and still need a bit of final tweeking on the full STM setup but it is really close and I'm happy with the results.

STM Rage VI Primary
STM First Gen Secondary
14" MSA Wheels
30" Motoclaw Tires
Alex Reed Bumper powdercoated black
40" Rigid Light (Holy crap is that thing BRIGHT!!!)
Pair of D2 Flood's on the side (Mounted them right into the old seat belt attachment bungs!)
Crow Harness's
3/8" UHMW Skids

All around awesome machine! Sure, they have some issues, but show me one that doesn't!

Screenshot_2013-08-14-22-17-28_resized.png Screenshot_2013-08-14-22-18-00_resized.png Screenshot_2013-08-14-22-18-12_resized.png Screenshot_2013-08-14-22-18-40_resized.png Screenshot_2013-08-14-22-18-59_resized.png Screenshot_2013-08-14-22-19-14_resized.png Screenshot_2013-08-14-22-19-24_resized.png
 

·
Registered
Joined
·
272 Posts
Damn that's sharp, you running a lift. If not you have any clearance issues with the tires.


Nathan
 

·
Registered
Joined
·
69 Posts
Discussion Starter #5
No lift. It might rub on the rear if I get crazy with a jump but so far no problems.

Damn that's sharp, you running a lift. If not you have any clearance issues with the tires.


Nathan
 

·
Registered
Joined
·
272 Posts
One more question, I'm going to put on my pro armor doors tomorrow. I was just getting things ready tonight and took off factory side bar just so I could kinda set doors up to look at it. I noticed the rear top tube section of door that slides onto the top post where factory side bar went has a ton of slop in it 1/4". Did yours have this much slop or was it snug when sliding it on.
 

·
Registered
Joined
·
69 Posts
Discussion Starter #7
If I remember correctly, the instructions say install time of a couple hours. Ummm not. I spent several hours just trying to figure out how it all went together. Passenger door fit perfect. Driver door wasn't even close. I ended up redrilling the top tube mount and the bottom slam latch mount to get everything to line up.
 

·
Registered
Joined
·
1,272 Posts
AReed, are u able to make that top loop on the bumper stick out more to the front rather then straight up an down??? Kinda like popo does with there pre-runner bumper? Also can u pm me a price?

Also will my dually led lights fit under they loop??
 

·
Vendor
Joined
·
6,219 Posts
AReed, are u able to make that top loop on the bumper stick out more to the front rather then straight up an down??? Kinda like popo does with there pre-runner bumper? Also can u pm me a price?

Also will my dually led lights fit under they loop??
Yeah that's no problem. Ill check on the Dually's tomorrow and PM you a price.
 

·
Registered
Joined
·
69 Posts
Discussion Starter #15
Thanks for the compliments guys! Got a chance to take it on a night ride Saturday. No problems at all. The 30" Motoclaws worked great Didn't get in any really deep mud but a little bit of everything. Hard pack, rocks, hill climbs, just floats over most everything.

Need to tweak the clutch still a bit. Low speed engagement is good but it almost seems to have a flat spot in it from about 4500-6000 where it doesn't shift as quick as I'd like. Once past that RPM, it pulls HARD, easily spinning those 30's!
 

·
Registered
Joined
·
272 Posts
Just curious how the tires were doing for ya, I'm thinking of getting same set up here soon. You notice if the back rubbed at any point, also did you get clutch lined out for the heavier tires.


Thanks,
Nathan
 

·
Registered
Joined
·
1,130 Posts
Just wanted to show you guys how it is coming together. Think I'm going to call it almost done, still would like to install a winch into the bumper and still need a bit of final tweeking on the full STM setup but it is really close and I'm happy with the results.

STM Rage VI Primary
STM First Gen Secondary
14" MSA Wheels
30" Motoclaw Tires
Alex Reed Bumper powdercoated black
40" Rigid Light (Holy crap is that thing BRIGHT!!!)
Pair of D2 Flood's on the side (Mounted them right into the old seat belt attachment bungs!)
Crow Harness's
3/8" UHMW Skids
When you get a chance, can you show close up pics of the floods attached to the side of cage? I like that idea....Thanks!
 
1 - 17 of 17 Posts
Top