Can-Am Maverick Forum banner
Cancel

can-am 39” Light Bar Wiring?

1191 Views 38 Replies 3 Participants Last post by  Exile31, 
Exile31
2
Hey Guys - just placing my can-am light bar and the wiring Instructions are a bit unclear. (Attached)

Not clear where to place the 3rd wire - it’s Dark Pink not black as stated (done BLK to BLK & Red to Red).

…and what is the White Terminal?

(Sport Roof & Overhead roof switch panel already fitted.)

Cheers.

See less See more
Reply
Save
Like
1 - 20 of 39 Posts
Exile31
2020RR said:
Welcome!

Might want to take a minute and introduce yourself and car in the "Members Introduction" section.
Click to expand...
Thank you - will do!
Reply
Save
Like
  • Like
Reactions: 1
Exile31
2020RR said:
based on the way the harness is built I would "Guess" it goes on the middle post. My guess is that is the accessory post that only turns on when the car is running..
Click to expand...
I tried that - light not working (with power on) both engine off and running?

This particular Instruction section (OP) make no sense. (Well at least not to me!)

Help please…
Reply
Save
Like
Exile31
2
2020RR said:
Can you take a better picture showing the wires that are hooked up to these posts (not the new ones), the cover is blocking them
Click to expand...

See less See more
Reply
Save
Like
Exile31
Appreciate your help - thanks.

I wasn’t sure whether I should install the relay as I believe one was already installed when the harness to the Roof Switch panel was installed. (By the Dealer). But tried that now - no difference.

Should I put the relay back in this harness? (Switch panel to roof light.)

As I have done everything else except connect the Dark Pink cable - that must be the missing link. But where to place it?
Reply
Save
Like
Exile31
Thank you. That’s one question answered.

When the Roof Switch Panel was installed the wiring harness connected the vehicle to the panel. It is the same harness (it seems) that I now have to connect the Panel to the Light Bar. Most of the ‘new’ harness is obsolete and tucked up in the Roof Panel. That’s why I wasn’t sure if I should install the new relay provided with the Light and there is no mention of this in the Instructions!
Reply
Save
Like
Exile31
Relay now reinstalled - will fix to panel. As you can see 90% of the harness is obsolete as Roof switch panel already connected to vehicle.
See less See more
Reply
Save
Like
Exile31
Relay now reinstalled - will fix to panel. As you can see 90% of the harness is obsolete as Roof switch panel already connected to vehicle.
View attachment 296370
Reply
Save
Like
Exile31
2020RR said:
If the car has been prewired then you should be able to just plug the light harness to the light and use the switch panel to turn it on.. Or am I confused?
Click to expand...
Reply
Save
Like
Exile31
That’s what I thought also!

Problem is - the last cable I don’t know where to place. Don’t want to guess and do damage to this expensive Light Bar!
See less See more
Reply
Save
Like
Exile31
Just to clarify - harness from vehicle to Roof switch panel was installed by Dealer. The Light bar requires a further harness (see last pic) to connect Panel to Light - which I am attempting to install. The BRP instructions were not so helpful!
Reply
Save
Like
Exile31
…
Reply
Save
Like
Exile31
Thanks.
But where should I place this:

See less See more
Reply
Save
Like
Exile31
2020RR said:
So you have a switch installed on the dash specifically for the "light bar"
Click to expand...
Yes - when I re-fix the roof switch panel.
See less See more
Reply
Save
Like
Exile31
2020RR said:
Just put the small red wire on the big red wire and see if the light comes on. It should trigger it and turn the relay on.
Click to expand...
Many thanks - trying that now 🤞😊
Reply
Save
Like
  • Like
Reactions: 1
Exile31
You are a Gentleman Sir - I thank you!

Let there be light! 😁

Will be dark here soon - pic to follow.

Thank you very much for your considerable assistance.

All the very best from Kings Landing (if you’re a GoT fan!)
Reply
Save
Like
  • Like
Reactions: 1
Exile31
2
Even in the daylight they make a difference!

See less See more
Reply
Save
Like
  • Like
Reactions: 1
Exile31
👍🏼😎
Reply
Save
Like
Exile31
2020RR said:
Take a pic of the back of the switch so we can wire it in properly.
Click to expand...
That’s the easy part - switch is mated to connector. Both BRP parts.
Reply
Save
Like
Exile31
TBH - I don’t know! Panel back up and fixed now. I’m a “if it ain’t broke don’t fix it” guy!

While it works I’m happy! 😂
Reply
Save
Like
  • Like
Reactions: 1
1 - 20 of 39 Posts
Can-Am Maverick Forum
A forum community dedicated to Can-Am Maverick owners and enthusiasts. Come join the discussion about performance, accessories, modifications, troubleshooting, maintenance, and more!
Full Forum Listing
Explore Our Forums
Maverick X3 Maverick Discussions Member Introduction Engine and Drivetrain Maverick Accessories
Top