Can-Am Maverick Forum banner

1 - 11 of 11 Posts

·
Moderator
Joined
·
160 Posts
Discussion Starter #1
Can-Am Maverick 1000R Accessories - Make It Your Own!


The most powerful side-by-side vehicle in the industry,* the Can-Am® MaverickTM is a force to be reckoned with, and we have the accessories to enhance your riding experience even more. Make the best side-by-side vehicle even better with these essential add-ons built rugged and designed for easy installation, and see the difference genuine Can-Am Off-road Accessories can make.

Baja Style Spare Tire Holder

Because you never know where you’ll be when misfortune strikes, the cool look- ing Baja Style Spare Tire Holder could save your day. Its design allows for fast installation and removal of the tire with specifically designed tie-down straps. It is also compatible with or without the Wheel Jack.
maverick-rear.jpg

Wheel Jack

Without a doubt a must-have accessory to change a flat out on the trail. Its large base offers more stability, even on soft ground, and it includes a 17 mm wrench to remove the wheel nuts.
Wheel_Jack.jpg

Sport Aluminum Doors

These bolt-on doors are made of lightweight aluminum. Designed to open wide and rearward, and equipped with a slam latch and door catch, they allow the driver and passenger to get in and out easily. Their powder coated black paint adds a custom and bold look that will get you noticed.
Sport_Aluminum_Doors.jpg

Trailering and Storage Cover

Can-Am branded 300-denier solution-dyed cover.
Water repellent polyester construction. It fits with or without: roof, light rack, rear bumper, front bumper, side mirrors and spare tire holder. It has a trap for fuel and access to passenger area. You can attach it securely to your vehicle thanks to the heavy-duty cord around the bottom. It features soft material in the windshield area to prevent scratches while trailering.
TraileringCover.jpg

Rear Bumper

Made of heavy-duty 1.5 inch(4cm) steel tube with 1/8” skid plate
Rear receiver hitch compatible
Rear_Bumper.jpg

Receiver Hitch

Heavy duty 2” receiver hitch, 1,300 pounds of pulling capacity.
Receiver_Hitch.jpg

Front Skid Plate

Draw-formed 5052-H32 aluminum plate
3/16 inch (4.5mm) thick for durability and strength
Engraved Can-Am logo

Front Lateral Skid Plate

Draw-formed 5052-H32 aluminum plate
3/16 inch (4.5mm) thick for durability and strength - Engraved Can-Am logo
Sold in pairs


Rock Slider Bar

Made of heavy-duty 1.5 inch(4cm) steel tube
Lightweight

Rear Skid Plate

5052-H32 aluminum plate
3/16 inch (4.5mm) thick for durability and strength
Engraved Can-Am logo

A-Arm Protectors

5052-H32 aluminum plate and plastic deflector
3/16 inch(4.5mm) thick for durability and strength
Engraved Can-Am logo
Sold in pairs

Trailing Arm Protectors

5052-H32 aluminum plate
3/16 inch (4.5mm) thick for durability and strength
Engraved Can-Am logo
Sold in pairs

SkidPlates.jpg

Cargo Bed Liner

Made of durable polyethylene plastic with drain holes, it covers the rear end of your Maverick for endless cargo possibilities. With 4 solid mounting locations to attach your items, you can now carry almost anything you want and need, like a cooler. No tools required to install or remove the Cargo Bed Liner. It can even be used with the Baja Style Spare Tire Holder.
Cargo_BedLiner.jpg

Can-Am Maverick 1000R Accessories - Windshield Lineup

Adding a windshield to your Can-Am Maverick will give you instant protection against wind and debris while riding. The Can-Am lineup offers three easy-to- install options to fit all riding styles and conditions.

Full Windshield (Hardcoated)

It combines the utmost in protection from the elements with optical clarity while riding. The hardcoated polycarbonate material on both sides offers better impact and abrasion resistance, as well as prolonged protection against wear- and-tear for a longer “like-new” look than acrylic windshields. The windshield also features non-yellowing, non-crazing, non-cracking and UV-resistant properties. The quick-attach brackets procure fast, easy and tool-less installation and removal.

Full Windshield

Thanks to its durable polycarbonate construction, the Full Windshield is de- signed for optical clarity and better impact resistance than acrylic windshields. It also features non-yellowing, non-crazing, non-cracking and UV-resistant properties. The quick-attach brackets procure fast, easy and tool-less installation and removal.

Half Windshield

Designed for protection from wind and debris as well as optical clarity, the rugged, durable polycarbonate construction offers better impact resistance than acrylic windshields. It features a reverse angle lip to deflect air flow, and non- yellowing, non-crazing, non-cracking and UV-resistant properties. The quick-attach brackets procure fast, easy and tool-less installation and removal.
FullWindshield.jpg

Fully Accessorized Maverick.jpg

12V Power Outlet

Cargo box mounted 12V accessories outlet. Easy plug-in harness included. Practical for those electrical carry-ons.
12V_Outlet.jpg

Baja Style Spare Tire Holder

Because you never know where you’ll be when misfortune strikes, the cool look- ing Baja Style Spare Tire Holder could save your day. Its design allows for fast installation and removal of the tire with specifically designed tie-down straps. It is also compatible with or without the Wheel Jack.
Baja_Spare_Tire_Holder.jpg

Bimini Roof With Sun Visor

Here’s a versatile accessory that lets you choose the level of protection you need to fit the moment. The soft top can be rolled up on the hard visor, allowing more air in and letting you enjoy the sun. The hard visor also gives you the possibility of installing the Can-Am light rack, for extra lighting and a custom look.
Bimini_Roof_With_Visor.jpg
 

·
Registered
Joined
·
649 Posts
I don't understand why you need no tools to mount the bed liner.... Also those doors are too low cut....Overall I thinks this thing will be awesome
 

·
Registered
Joined
·
400 Posts
love those doors, awesome, long slug better for leaning on
 

·
Registered
Joined
·
33 Posts
I'm quite fond of Can-am printed on the rear net...although I prefer the Polaris netting material.
Maybe I just need to manufacture my own. LOL
 

·
Registered
Joined
·
1 Posts
Im interested in replacing my older commaner model with this puppy, she looks mean! But im curious to know what kind of gps if any you guys use? I currently have rather simple iPhone car mount i use for gps, what are some alternatives?
 

·
Registered
Joined
·
1,298 Posts
check ou this video of mine, it shows lots of accsy's close up. it also shows how this can be a oen maverick limited, with new dash, pretty cool how they had it. sort of a limited inside.




Im interested in replacing my older commaner model with this puppy, she looks mean! But im curious to know what kind of gps if any you guys use? I currently have rather simple iPhone car mount i use for gps, what are some alternatives?
 

·
Registered
Joined
·
355 Posts
Im interested in replacing my older commaner model with this puppy, she looks mean! But im curious to know what kind of gps if any you guys use? I currently have rather simple iPhone car mount i use for gps, what are some alternatives?
The interior is the same as the Commander. There are various GPS mounts currently available that allows you to install a full size GPS like the HDS-5 from Lowrance. We build a mount that replaces the center plastic so one can be mounted. The Lowrance units are the standard in off road racing but are more technical to use.
 

·
Registered
Joined
·
1,072 Posts
1 - 11 of 11 Posts
Top